We now have a shorter (20 mm) 12 mm Hex Wheel Adapter for 6 mm Shaft as an alternative to our original 35 mm extended version. These adapters work well with our 37D mm metal gearmotors, allowing you to use them with many common hobby RC wheels.

12mm Hex Wheel Adapter for 6mm Shaft connecting a Wild Thumper Wheel to a 37D mm Metal Gearmotor.

For our full selection of these adapters, see our hex wheel adapter category.

Related products

	12mm Hex Wheel Adapter for 6mm Shaft (2-Pack)
	12mm Hex Wheel Adapter for 6mm Shaft, Extended (2-Pack)
	Dagu Wild Thumper Wheel 120x60mm Pair with 4mm Shaft Adapters - Metallic Red
	Dagu Wild Thumper Wheel 120x60mm Pair with 4mm Shaft Adapters - Chrome

We have two exciting new DC motor driver carriers to introduce, one for ROHM’s BD65496MUV and one for Maxim’s MAX14870:

BD65496MUV Single Brushed DC Motor Driver Carrier, labeled top view.

MAX14870 Single Brushed DC Motor Driver Carrier, labeled top view.

These drivers each offer wide operating voltage ranges, with the BD65496MUV operating from as low as 2 V up to 16 V and the MAX14870 operating from 4.5 V all the way up to 36 V. They can each supply over an amp to a single, bidirectional brushed DC motor. These are the highest-performing integrated motor drivers we know of short of substantially larger units such as the MC33926 and VNH5019. For more information on these drivers, click on the related products below:

Related products

	BD65496MUV Single Brushed DC Motor Driver Carrier
	MAX14870 Single Brushed DC Motor Driver Carrier

We are excited to introduce new versions of our high-power micro metal gearmotors with long-life carbon brushes in place of the standard precious metal brushes:

Micro Metal Gearmotor HPCB long-life carbon brushes (left) next to Micro Metal Gearmotor HP precious metal brushes (right).

So far, we only offer these on motors with HP windings, so the brushes being a lot more robust can just move the failure point if you try to push the motors too hard. However, if you use them at around 6 V and keep the continuous load under around 20% of the stall torque, the carbon brushes allow the HPCB motors to last several times longer than HP versions with precious metal brushes.

With the addition of this new HPCB motor variant in ten different gear ratios (10:1 through 1000:1), our selection of popular micro metal gearmotors now spans more than fifty options, giving you control over the motor winding, gearbox, and shaft arrangement:

Motor Type	Stall Current @ 6 V	No-Load Speed @ 6 V	Approximate Stall Torque @ 6 V	Single-Shaft (Gearbox Only)	Dual-Shaft (Gearbox & Motor)
high-power, carbon brushes (HPCB)	1600 mA	3000 RPM	4 oz-in	10:1 HPCB
		1000 RPM	9 oz-in	30:1 HPCB
		625 RPM	15 oz-in	50:1 HPCB
		400 RPM	22 oz-in	75:1 HPCB
		320 RPM	30 oz-in	100:1 HPCB
		200 RPM	40 oz-in	150:1 HPCB
		140 RPM	50 oz-in	210:1 HPCB
		120 RPM	60 oz-in	250:1 HPCB
		100 RPM	70 oz-in	298:1 HPCB
		32 RPM	125 oz-in	1000:1 HPCB
high-power (HP) (same specs as HPCB above)	1600 mA	6000 RPM	2 oz-in	5:1 HP
		3000 RPM	4 oz-in	10:1 HP	10:1 HP dual-shaft
		1000 RPM	9 oz-in	30:1 HP	30:1 HP dual-shaft
		625 RPM	15 oz-in	50:1 HP	50:1 HP dual-shaft
		400 RPM	22 oz-in	75:1 HP	75:1 HP dual-shaft
		320 RPM	30 oz-in	100:1 HP	100:1 HP dual-shaft
		200 RPM	40 oz-in	150:1 HP	150:1 HP dual-shaft
		140 RPM	50 oz-in	210:1 HP
		120 RPM	60 oz-in	250:1 HP
		100 RPM	70 oz-in	298:1 HP	298:1 HP dual-shaft
		32 RPM	125 oz-in	1000:1 HP	1000:1 HP dual-shaft
medium-power (MP)	700 mA	2200 RPM	3 oz-in	10:1 MP	10:1 MP dual-shaft
		730 RPM	8 oz-in	30:1 MP
		420 RPM	13 oz-in	50:1 MP
		290 RPM	17 oz-in	75:1 MP	75:1 MP dual-shaft
		220 RPM	19 oz-in	100:1 MP	100:1 MP dual-shaft
		150 RPM	24 oz-in	150:1 MP
		75 RPM	46 oz-in	298:1 MP
		25 RPM	80 oz-in	1000:1 MP	1000:1 MP dual-shaft
low-power	360 mA	2500 RPM	1 oz-in	5:1
		1300 RPM	2 oz-in	10:1
		440 RPM	4 oz-in	30:1	30:1 dual-shaft
		250 RPM	7 oz-in	50:1	50:1 dual-shaft
		170 RPM	9 oz-in	75:1
		120 RPM	12 oz-in	100:1	100:1 dual-shaft
		85 RPM	17 oz-in	150:1
		60 RPM	27 oz-in	210:1
		50 RPM	32 oz-in	250:1
		45 RPM	40 oz-in	298:1	298:1 dual-shaft
		14 RPM	70 oz-in	1000:1	1000:1 dual-shaft

Related products

	10:1 Micro Metal Gearmotor HPCB 6V
	30:1 Micro Metal Gearmotor HPCB 6V
	50:1 Micro Metal Gearmotor HPCB 6V
	75:1 Micro Metal Gearmotor HPCB 6V
	100:1 Micro Metal Gearmotor HPCB 6V
	150:1 Micro Metal Gearmotor HPCB 6V
	210:1 Micro Metal Gearmotor HPCB 6V
	250:1 Micro Metal Gearmotor HPCB 6V
	298:1 Micro Metal Gearmotor HPCB 6V
	1000:1 Micro Metal Gearmotor HPCB 6V

We are now selling the low-profile 2×7 male LCD header included with the Zumo 32U4 robot kit.

Related products

	0.100" (2.54 mm) Low-Profile Male Header: 2×7-Pin, 8.75 mm
	8×2 Character LCD - Black Bezel (Parallel Interface)

Make your next project more colorful with our new red, white, blue, and yellow breakaway male header strips. You can use them to add some personal flair to an otherwise boring PCB, or you can use them to color-code connections, like on this custom-assembled 24-channel Mini Maestro:

Like our venerable black breakaway male header strip, these strips are 40 pins long, but they can easily be cut or broken into smaller strips that work with standard 0.1″-pitch through-holes, female connectors, and breadboards.

We also now have right angle male header strips available in 2 rows or 3 rows:

0.100" (2.54 mm) Breakaway Male Header: 2×40-Pin, Right Angle.

0.100" (2.54 mm) Breakaway Male Header: 3×40-Pin, Right Angle.

We are particularly excited about the 3×40 right angle header because it can be used with the partial kit versions of our Maestro servo controllers to make low-profile modules where the servos plug in from the side rather than the top.

Related products

	0.100" (2.54 mm) Breakaway Male Header: 1×40-Pin, Straight, Black
	0.100" (2.54 mm) Breakaway Male Header: 1×40-Pin, Straight, White
	0.100" (2.54 mm) Breakaway Male Header: 1×40-Pin, Straight, Red
	0.100" (2.54 mm) Breakaway Male Header: 1×40-Pin, Straight, Yellow
	0.100" (2.54 mm) Breakaway Male Header: 1×40-Pin, Straight, Blue
	0.100" (2.54 mm) Breakaway Male Header: 2×40-Pin, Right Angle
	0.100" (2.54 mm) Breakaway Male Header: 3×40-Pin, Right Angle
	Mini Maestro 24-Channel USB Servo Controller (Partial Kit)
	Mini Maestro 18-Channel USB Servo Controller (Partial Kit)
	Mini Maestro 12-Channel USB Servo Controller (Partial Kit)
	Micro Maestro 6-Channel USB Servo Controller (Partial Kit)

We now have 40mm-diameter wheels (available in black, red, and white) in the same thin style as our 32×7 mm wheels, which help fill the void between those and the 60×8 mm wheels that were previously our next size up.

Black Pololu Wheels with 90, 80, 70, 60, 40, and 32 mm diameters (other colors available).

Like the rest of the Pololu wheels, the 40×7 mm wheels press-fit onto the 3mm D shafts on many of our motors, including the micro metal gearmotors and mini plastic gearmotors.

Pololu 40×7mm wheel on a Micro Metal Gearmotor.

For more information, take a look at one of the items listed below, or check out all the Pololu wheels category page for more options.

Related products

	Pololu Wheel 40×7mm Pair - Black
	Pololu Wheel 40×7mm Pair - Red
	Pololu Wheel 40×7mm Pair - White

A customer of ours who is a software engineer in Seattle made this detailed video showing how to assemble the new Zumo 32U4 robot kit. Thanks for sharing it with us, Jamie!

Related products

Zumo 32U4 Robot Kit (No Motors)

We are now offering Sharp’s GP2Y0A60SZLF analog distance sensor by itself. This is a great sensor with a wide 4″ to 60″ (10 cm to 150 cm) detection range and a high update rate of 60 Hz, but it requires additional components to use and has a non-standard 1.5 mm pitch. You can use this sensor with our compact carrier boards to make a complete sensor module, or you can get our carrier boards with the GP2Y0A60SZLF already installed.

For more information, see the GP2Y0A60SZLF product page.

Related products

	Sharp/Socle GP2Y0A60SZLF Analog Distance Sensor 10-150cm
	Pololu Carrier with Sharp/Socle GP2Y0A60SZLF Analog Distance Sensor 10-150cm, 5V
	Pololu Carrier with Sharp/Socle GP2Y0A60SZLF Analog Distance Sensor 10-150cm, 3V
	Pololu Carrier for Sharp/Socle GP2Y0A60SZLF Analog Distance Sensor, 5V
	Pololu Carrier for Sharp/Socle GP2Y0A60SZLF Analog Distance Sensor, 3V

PeterPan, an active member of our forum, recently started a thread asking other Wixel users to push for us to get Wixels FCC certified. The Wixel is getting to be one of our older products, so it is due for some updates, too (e.g., our new USB products have moved on to Micro-B connectors). We realize many of our customers do not necessarily want to publicly discuss their projects, so if you do not feel like participating in the forum thread, please feel free to contact us directly about your thoughts on FCC certification and other ways you would like to see the Wixel improved.

Related products

Wixel Programmable USB Wireless Module (Fully Assembled)

Tomorrow is Arduino Day, and we are joining in on the fun by offering big discounts on many of our Arduino-related products, including our A-Star programmable controllers and Arduino shields. The sale has already started, and it will run through the end of Sunday (I know, Arduino Day is a one-day event, but this makes sure the sale lasts all Arduino Day in every time zone). You can find all of the sale items on our Arduino Day 2015 sale page.