Cyber Week Sale – click for coupon codes!

12V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors

These Micro Metal Gearmotors have high-power, 12 V motors with a stall current of 750 mA and a typical free-run current of 80 mA. They feature long-life carbon brushes and offer approximately the same performance at 12 V as the 6V HPCB versions offer at 6 V, just with half the current draw. The following table shows all of the versions available with the HPCB 6V motor:

HPCB 12V
(high-power, carbon brushes)
Rated
Voltage
Stall
Current
No-Load
Current
No-Load
Speed
(RPM)
Extrapolated
Stall Torque
Max
Power
(W)
Approx
Gear
Ratio


No Encoder

w/ Extended
Motor Shaft

w/ Encoder,
Back Conn.

w/ Encoder,
Side Conn.
(kg⋅cm) (oz⋅in)
12 V 0.75 A 100 mA 6800 0.09 1.3 5:1 #3036 #3047 #5204 #5205
80 mA 3400 0.17 2.4 1.5 10:1 #3037 #3048 #5206 #5207
2200 0.25 3.5 1.4 15:1 #4788 #4789 #5208 #5209
1100 0.39 5.4 1.1 30:1 #3038 #3049 #5210 #5211
650 0.67 9.3 1.1 50:1 #3039 #3050 #5212 #5213
450 1.0 14 1.1 75:1 #3040 #3051 #5214 #5215
330 1.3 18 1.1 100:1 #3041 #3052 #5216 #5217
220 1.8 25 1.0 150:1 #3042 #3053 #5218 #5219
160 2.5 35 1.0 210:1 #3043 #3054 #5220 #5221
130 3.0 42 1.1 250:1 #3044 #3055 #5222 #5223
110 3.3 46 1.0 298:1 #3045 #3056 #5224 #5225
85 5.0 69 1.1 380:1 #4798 #4799 #5226 #5227
35 10 140 1000:1 #3046 #3057 #5228 #5229

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

Versions with other motors are also available. You can use the following selection boxes to choose from all of our Micro Metal Gearmotors versions:

Alternatives available with variations in these parameter(s): gear ratio motor type encoder Select variant…

Products in category “12V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors”

Pololu item #: 3036
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 4.995:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 6800 RPM, 100 mA 0.09 kg⋅cm (1 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3047
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 4.995:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 6800 RPM, 100 mA 0.09 kg⋅cm (1 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3037
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 9.96:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 3400 RPM, 80 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3048
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 9.96:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 3400 RPM, 80 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5206
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 9.96:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 3400 RPM, 80 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5207
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 9.96:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 3400 RPM, 80 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4788
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 15.25:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 2200 RPM, 80 mA 0.25 kg⋅cm (3.5 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4789
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 15.25:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 2200 RPM, 80 mA 0.25 kg⋅cm (3.5 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5208
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 15.25:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 2200 RPM, 80 mA 0.25 kg⋅cm (3.5 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5209
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 15.25:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 2200 RPM, 80 mA 0.25 kg⋅cm (3.5 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3038
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 29.86:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 1100 RPM, 80 mA 0.39 kg⋅cm (5.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3049
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 29.86:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 1100 RPM, 80 mA 0.39 kg⋅cm (5.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5210
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 29.86:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 1100 RPM, 80 mA 0.39 kg⋅cm (5.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5211
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 29.86:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 1100 RPM, 80 mA 0.39 kg⋅cm (5.4 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3039
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 51.45:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 650 RPM, 80 mA 0.67 kg⋅cm (9.3 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3050
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 51.45:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 650 RPM, 80 mA 0.67 kg⋅cm (9.3 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5212
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 51.45:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 650 RPM, 80 mA 0.67 kg⋅cm (9.3 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5213
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 51.45:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 650 RPM, 80 mA 0.67 kg⋅cm (9.3 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3040
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 75.81:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 450 RPM, 80 mA 1.0 kg⋅cm (13 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3051
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 75.81:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 450 RPM, 80 mA 1.0 kg⋅cm (13 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5214
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 75.81:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 450 RPM, 80 mA 1.0 kg⋅cm (13 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5215
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 75.81:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 450 RPM, 80 mA 1.0 kg⋅cm (13 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3041
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 100.37:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 330 RPM, 80 mA 1.3 kg⋅cm (18 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3052
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 100.37:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 330 RPM, 80 mA 1.3 kg⋅cm (18 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5216
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 100.37:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 330 RPM, 80 mA 1.3 kg⋅cm (18 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5217
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 100.37:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 330 RPM, 80 mA 1.3 kg⋅cm (18 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3042
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 150.58:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 220 RPM, 80 mA 1.8 kg⋅cm (24 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3053
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 150.58:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 220 RPM, 80 mA 1.8 kg⋅cm (24 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5218
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 150.58:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 220 RPM, 80 mA 1.8 kg⋅cm (24 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5219
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 150.58:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 220 RPM, 80 mA 1.8 kg⋅cm (24 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3043
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 210.59:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 160 RPM, 80 mA 2.5 kg⋅cm (34 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3054
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 210.59:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 160 RPM, 80 mA 2.5 kg⋅cm (34 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5220
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 210.59:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 160 RPM, 80 mA 2.5 kg⋅cm (34 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5221
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 210.59:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 160 RPM, 80 mA 2.5 kg⋅cm (34 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3044
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 248.98:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 130 RPM, 80 mA 3.0 kg⋅cm (41 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3055
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 248.98:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 130 RPM, 80 mA 3.0 kg⋅cm (41 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5222
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 248.98:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 130 RPM, 80 mA 3.0 kg⋅cm (41 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5223
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 248.98:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 130 RPM, 80 mA 3.0 kg⋅cm (41 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3045
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 297.92:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 110 RPM, 80 mA 3.3 kg⋅cm (45 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3056
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 297.92:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 110 RPM, 80 mA 3.3 kg⋅cm (45 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5224
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 297.92:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 110 RPM, 80 mA 3.3 kg⋅cm (45 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5225
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 297.92:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 110 RPM, 80 mA 3.3 kg⋅cm (45 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4798
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 379.17:1 with high-durability steel plates no encoder

voltage no-load performance stall extrapolation*
12 V 85 RPM, 80 mA 5.0 kg⋅cm (69 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4799
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 379.17:1 with high-durability steel plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 85 RPM, 80 mA 5.0 kg⋅cm (69 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5226
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 85 RPM, 80 mA 5.0 kg⋅cm (69 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5227
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 85 RPM, 80 mA 5.0 kg⋅cm (69 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3046
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 986.41:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
12 V 35 RPM, 80 mA 10 kg⋅cm (138 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3057
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 986.41:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
12 V 35 RPM, 80 mA 10 kg⋅cm (138 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5228
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 986.41:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 35 RPM, 80 mA 10 kg⋅cm (138 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5229
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 986.41:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 35 RPM, 80 mA 10 kg⋅cm (138 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5204
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 4.995:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
12 V 6800 RPM, 100 mA 0.09 kg⋅cm (1 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5205
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 12V: high-power 12V with carbon brushes 4.995:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
12 V 6800 RPM, 100 mA 0.09 kg⋅cm (1 oz⋅in), 0.75 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Related Products

Magnetic Encoder Pair Kit with Top-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit with Side-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Pololu Micro Metal Gearmotor Bracket Extended Pair
Pololu Micro Metal Gearmotor Bracket Pair - Black
Pololu Micro Metal Gearmotor Bracket Pair - White
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, #2-56 Holes (2-Pack)
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, M3 Holes (2-Pack)
12mm Hex Wheel Adapter for 3mm Shaft (2-Pack)
Machine Screw: M1.6, 3mm Length, Phillips (6-pack)
MAX14870 Single Brushed DC Motor Driver Carrier
DRV8801 Single Brushed DC Motor Driver Carrier
A4990 Dual Motor Driver Carrier
Pololu A4990 Dual Motor Driver Shield for Arduino
26:1 Sub-Micro Plastic Planetary Gearmotor 6Dx16L mm
136:1 Sub-Micro Plastic Planetary Gearmotor 6Dx19L mm

Related Categories

Micro Metal Gearmotors
6V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors
6V High-Power (HP) Micro Metal Gearmotors
6V Medium-Power (MP) Micro Metal Gearmotors
6V Low-Power (LP) Micro Metal Gearmotors
Encoders for Micro Metal Gearmotors
Pololu Wheels and Tracks
Brushed DC Motor Controllers
Brushed DC Motor Drivers
Current Sensors
Pololu 5″ Robot Chassis RRC04A
20D Metal Gearmotors
Pololu Metal Gearmotors
Pololu Plastic Gearmotors
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors