Encoders for Micro Metal Gearmotors

Products in category “Encoders for Micro Metal Gearmotors”

Pololu item #: 4760
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and Hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. These encoders have a top-entry, 6-pin male JST SH-type connector, and we have cables that work with them available in several lengths (12 cm, 30 cm, and 75 cm). This module is compatible with all of the dual-shaft micro metal gearmotors we carry, including the HPCB versions.

Pololu item #: 4761
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and Hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. These encoders have a side-entry, 6-pin male JST SH-type connector, and we have cables that work with them available in several lengths (12 cm, 30 cm, and 75 cm). This module is compatible with all of the dual-shaft micro metal gearmotors we carry, including the HPCB versions.

Pololu item #: 3081
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and Hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. These encoders have their pins arranged as through-holes on a 2mm pitch, and wires or 2mm-pitch connectors must be soldered in to use them. This module is compatible with all of the dual-shaft micro metal gearmotors we carry, including the HPCB versions.

Pololu item #: 2599
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

These magnetic discs can be used with our micro metal gearmotors with extended motor shafts as part of a quadrature encoder system that offers 12 counts per revolution. They are 2 mm thick with an outer diameter of 7.65 mm and an inner diameter of 1.0 mm. Appropriate Hall Effect sensors, such as those in our magnetic encoder pair kit with top-entry connector for micro metal gearmotors, are required to complete the system. These discs are bulk-packaged and must be ordered in multiples of five.

Pololu item #: 2590
Brand: Pololu supply outlook
Status: Active 
RoHS 3 compliant
Out of stock.
Quantity:

Add quadrature encoders to your LP, MP, or HP micro metal gearmotors (extended back shaft version required) with this kit consisting of two sensor boards, two 3-tooth encoder wheels, and two 5-tooth encoder wheels. The installed system does not exceed the 12 mm × 10 mm cross section of the motors and extends only 5 mm beyond the plastic motor end cap. The 3-tooth wheel provides 12 counts per revolution; using the 5-tooth wheel yields 20 counts per revolution. This version is intended for use at 5 V.

Note: This board is not compatible with the HPCB micro metal gearmotors; it is only compatible with LP, MP, and HP dual-shaft micro metal gearmotors.

Pololu item #: 2591
Brand: Pololu supply outlook
Status: Active 
RoHS 3 compliant
Out of stock.
Quantity:

Add quadrature encoders to your LP, MP, or HP micro metal gearmotors (extended back shaft version required) with this kit consisting of two sensor boards, two 3-tooth encoder wheels, and two 5-tooth encoder wheels. The installed system does not exceed the 12 mm × 10 mm cross section of the motors and extends only 5 mm beyond the plastic motor end cap. The 3-tooth wheel provides 12 counts per revolution; using the 5-tooth wheel yields 20 counts per revolution. This version is intended for use at 3.3 V.

Note: This version is not compatible with the HPCB micro metal gearmotors; it is only compatible with LP, MP, and HP dual-shaft micro metal gearmotors.

Related Categories

Encoders
Micro Metal Gearmotors with Extended Motor Shafts
6-Pin JST SH-Style Cables
6-Pin JST SH-Style Connector Boards
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors