Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a TI DRV8834 driver and ships with soldered header pins and terminal blocks. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2 A max with sufficient additional cooling).
Alternatives available with variations in these parameter(s): model connectors soldered?
|Description||Specs (15)||Pictures (8)||Resources (25)||FAQs (1)||On the blog (5)|
The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial. They also offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer).
The table below lists the members of the Tic family and shows the key differences among them.
|Operating voltage range:||4.5 V to 35 V(1)||2.5 V to 10.8 V||8.5 V to 45 V(1)||10 V to 47 V(1)|
|Max continuous current per phase
(no additional cooling):
|1.5 A||1.5 A||1.5 A||1.8 A|
|Peak current per phase
(additional cooling required):
|2.5 A||2 A||2.5 A||4.5 A|
|Automatic decay selection:|
|Automatic gain control (AGC):|
|Price (connectors not soldered):||$19.95||$29.95||$29.95||$39.95|
|Price (connectors soldered):||$21.95||$31.95||$31.95||$41.95|
1 See product pages and user’s guide for operating voltage limitations.
Tic T500 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.
Tic T834 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.
Tic T825 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.
Tic T249 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.
Features and specifications
- Open-loop speed or position control of one bipolar stepper motor
- A variety of control interfaces:
- USB for direct connection to a computer
- TTL serial operating at 5 V for use with a microcontroller
- I²C for use with a microcontroller
- RC hobby servo pulses for use in an RC system
- Analog voltage for use with a potentiometer or analog joystick
- Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (not for position feedback)
- STEP/DIR inputs for compatibility with existing stepper motor control firmware
- Acceleration and deceleration limiting
- Maximum stepper speed: 50,000 steps per second
- Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).
- Up to six different microstep resolutions:
- The Tic T825, Tic T834, and T249 support full step, half step, 1/4 step, 1/8 step, 1/16 step, and 1/32 step
- The Tic T500 supports full step, half step, 1/4 step, 1/8 step
- Digitally adjustable current limit
- Optional safety controls to avoid unexpectedly powering the motor
- Input calibration (learning) and adjustable scaling degree for analog and RC signals
- 5 V regulator (no external logic voltage supply needed)
- Optional limit switch inputs with homing capabilities
- Optional kill switch inputs
- STEP/DIR outputs for controlling external stepper motor drivers
- Connects to a computer through USB via a USB A to Micro-B cable (not included)
- Free configuration software available for Windows, Linux, and macOS
- Arduino library makes it easy to get started using these controllers with an Arduino or compatible board
- Comprehensive user’s guide
Details for item #3132
The Tic T834 is based on the DRV8834 IC from Texas Instruments. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A continuous per phase without a heat sink or forced air flow (the peak current per phase is 2 A). This version is sold with connectors soldered so no soldering is necessary to use it.
Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered).
A version is also available with header pins and terminal blocks included but not soldered.
People often buy this product together with:
|Tic T825 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)|
|Stepper Motor: Bipolar, 200 Steps/Rev, 42×38mm, 2.8V, 1.7 A/Phase|
|Stepper Motor: Bipolar, 200 Steps/Rev, 20×30mm, 3.9V, 0.6 A/Phase|