New adjustable voltage regulators with multi-turn fine adjustment

Posted by Jan on 4 December 2017

I am excited to announce our first voltage regulators with multi-turn trimmer potentiometers! I have wanted to add multi-turn pots to our products for a long time, but the problem has been that they are really expensive. They also tend to be quite big, at least compared to many of our boards, which we try to keep compact, and the smaller, surface-mounted ones are especially expensive. My latest round of looking for lower-cost options did not pan out, but I decided to just give it a try with the expensive parts.

The new S9V11x regulators that feature these potentiometers are buck-boost regulators that can output a voltage that is lower, the same, or higher than the input voltage. There are also versions with a multi-turn pot for adjusting the undervoltage cutoff threshold, so that if you use these with batteries, you can prevent overdischarging them. With twelve turns of adjustment available, it’s much easier to precisely set the voltages on the modules than with the single-turn potentiometers we have used on other adjustable regulators.

The output and cutoff multi-turn adjustment potentiometers on the S9V11x voltage regulators.

While I have been talking mostly about the potentiometers, the main regulator is pretty magical, too, giving you quite a bit of power over a broad operating input range in a small size.

Typical maximum continuous output current of Step-Up/Step-Down Voltage Regulator S9V11x

Our stock products are available in several combinations of adjustable and fixed output voltage and cutoff. If you have a higher-volume application, we can make them with fixed voltages wherever you need them. You could initially prototype your design with the adjustable version and then get fixed ones made once you know exactly what voltage you need.

Regulator Input (V) Output (V) Low-voltage cutoff Size Price
#2868 S9V11MACMA 2* – 16 2.5 – 9 (fine-adjust) fine-adjust 0.50″ × 0.60″ × 0.25″ $13.95
#2869 S9V11MA 2.5 – 9 (fine-adjust) $10.95
#2870 S9V11F5S6CMA 5 (6 V selectable) fine-adjust $10.95
#2871 S9V11F3S5CMA 3.3 (5 V selectable) fine-adjust $10.95
#2872 S9V11F3S5 3.3 (5 V selectable) 0.50″ × 0.60″ × 0.17″ $7.95
#2873 S9V11F3S5C3 3.3 (5 V selectable) 3 V (fixed) $7.95
#2836 S9V11F5 5 0.30″ × 0.45″ × 0.17″ $8.95
* The regulator has a minimum start-up voltage of 3 V, but it can operate down to 2 V after startup. It is disabled when the input voltage is below the low-voltage cutoff.

I am very interested to see what people think of the multi-turn adjustment feature. If these new regulators sell decently or customers ask for it, we will add the multi-turn potentiometers to our other regulator offerings. Is the extra expense worth it? Or do you know of a good, low-cost, multi-turn potentiometer we could consider for future products like this?

15 comments

Like this device. Would like to see it in a 2.5 to 15 volt output version.
Thanks for the feedback. That higher output range you are asking for is not feasible on this particular design. Do you need the 3-16V input range in the same device, or are you wanting the higher output voltage for an application where the input voltage range would be smaller? (I'm asking because it's much easier to make just a step-up converter for low input voltage applications, and the step down/step up (or even straight step down) functionality would be easier to achieve if it did not have to operate at so low of a voltage.)

- Jan
It would be nice if there was a low voltage led tied to the lvc. Set up 0.5v above the cutoff would be perfect. Maybe even adjustable
Hi, Patrick.

Thanks for your feedback! Adding a low voltage indicator LED and circuit would add to the current draw and size of the board, so I am not sure the trade offs would be worth it for a general-purpose regulator, but we will keep it in mind. You could also add a circuit like that externally to the regulator's VIN or EN pins. If you have a high-volume application for such a regulator, please let us know, and we can probably make it for you.

-Claire
Hello,

Is it a problem if there's 5v applied on the output pin? From another power source? Is there a diode on the output pin? I tried googling, but haven't found the answer.

Thanks!

Costyn.
Hi, Costyn.

You definitely should never connect the output of this regulator to another source when the regulator is on. The board does not include any protection from power flowing back into the regulator, and in generally two regulated power sources will likely fight each other if directly connected. If you need to do something like that, I recommend looking into ORing circuits.

-Claire
HI Claire,

Thanks for the response. I definitely won't be applying 5v to the output pin when the regulator is itself live. Just when I'm programming the attached microcontroller there'll be power on the 5v rail. When my project is installed it will be just the microcontroller.

Regards.
What controller is this converter using? Would be useful to know other parameters like soft start, current impulse response, etc...
Hello, Jose.

We do not disclose the regulator chip on those boards, but the soft start time is typically 850μs while boosting and 400μs while bucking. For information about other specific parameters please email us.

-Tony
Hi,
I'd like to know some details about the low-voltage-cutoff function:
-how do you reset it? (I guess removing input voltage and putting in back on resets it, which would be just what I want)
-if the battery voltage goes above a certain level, will the regulator switched on again automatically?

Best regards,
Simon
Hello, Simon.

Please refer to the "Setting the cutoff voltage" section of the product page, which answers both of your questions.

- Patrick
Hi, in order to switch on/off a S9V11MACMA board (#2868) can I connect the EN pin to ground via a switch? Also what are the consequences on the regulated voltage and current to vary the output voltage during use? Would that be feasible to offer a regulator with an external potentiometer? Alternatively could I remove the onboard voltage adjuster and connect an external potentiometer?
Hi, Ludovic.

Yes, a switch can be used to ground the EN line and put the regulator in low-power sleep mode. It is fine to adjust the output of the regulator while it is on. I am not sure I understand your question about offering an external potentiometer. You could remove and replace the on-board potentiometer. If the replacement potentiometer is not soldered directly to the board, I recommend keeping the connections as short as possible to minimize any issues.

-Claire
Hello,
is it possible to use 5v fixed stepdown (#2870) in car?
It's BEV with DC-DC to 12V. No alternator / ICE starting rubbish...

Best regards
kolaCZek
Hi, kolaCZek.

We would not recommend this for your application since we have many strictly step-down regulators that have a higher maximum input voltage, which would give you more margin on the high side. However, if your 12V source is actually clean and sure to stay under the 16V maximum input of the S9V11F5S6CMA regulator, you'll probably be fine. You might want to put an electrolytic cap on the input to prevent or limit any LC spikes on power-up that could go over 16V.

-Claire

Post a comment

Using your Pololu account allows you to customize your avatar and manage your comments; you can also post anonymously.

Related Products

2.5-9V Fine-Adjust Step-Up/Step-Down Voltage Regulator w/ Adjustable Low-Voltage Cutoff S9V11MACMA
2.5-9V Fine-Adjust Step-Up/Step-Down Voltage Regulator S9V11MA
5V Step-Up/Step-Down Voltage Regulator w/ Adjustable Low-Voltage Cutoff S9V11F5S6CMA
3.3V Step-Up/Step-Down Voltage Regulator w/ Adjustable Low-Voltage Cutoff S9V11F3S5CMA
3.3V Step-Up/Step-Down Voltage Regulator S9V11F3S5
3.3V Step-Up/Step-Down Voltage Regulator w/ Fixed 3V Low-Voltage Cutoff S9V11F3S5C3
5V Step-Up/Step-Down Voltage Regulator S9V11F5
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors