This is a merged information page for Item #3441.
View normal product page.
Pololu item #:
3441
Brand:
FEETECH
This version of the FS5103B standard servo from FEETECH is specially modified to provide access to the feedback potentiometer through a fourth (green) wire, allowing you to directly measure the position of the output. This extra information enables more complex robotics applications, such as determining when the servo has reached its target, detecting when the output is blocked, or implementing your own higher-level closed-loop position control.
Key specs at 6 V: 0.16 sec/60°, 53 oz-in (3.8 kg-cm), 43 g.
Compare all products in RC Servos or FEETECH Servos or FEETECH Servos with Feedback.
|
FEETECH Standard Servo FS5103B-FB with Position Feedback. |
|---|
 |
Servo and feedback connectors on the FEETECH servos with position feedback. |
|---|
 |
FEETECH Standard Servo FS5103B with included hardware (actual hardware might vary). |
|---|
 |
The FEETECH Standard Servo FS5103B has a plastic gear train and two ball bearings on the output. |
|---|
 |
The FEETECH FS5103B and Power HD 3001HB have nearly identical dimensions and similar performance. |
|---|
The FS5103B-FB is a specially modified version of FEETECH’s FS5103B standard-size analog servo that provides access to the feedback potentiometer through a fourth (green) wire, which makes it possible to directly measure the output angle. With this extra information, you can determine when the servo has reached its target position (or detect if something is interfering with its ability to get there). This feedback also enables more complex closed-loop control of the servo from your main controller.
Like the FS5103B, the FS5103B-FB works with standard RC servo pulses, providing a running angle of approximately 180° over a servo pulse range of 600 µs to 2400 µs. The feedback voltage varies linearly over this range by a couple of volts.
The servo signal, power, and ground are provided through a 3-wire servo cable that is terminated with a standard JR-style connector, which is Futaba-compatible. The feedback is accessible through a separate green wire that is terminated like our female premium jumper wires and works with standard 0.1″ male header pins. These cables are approximately 12″ (30 cm) long.
|
Servo and feedback connectors on the FEETECH servos with position feedback. |
|---|
For more information about this servo, see the FS5013B datasheet (133k pdf) (please note that this is the datasheet for the standard FS5103B, so it does not include any information about the special feedback modification).
|
FEETECH Standard Servo FS5103B with included hardware (actual hardware might vary). |
|---|
This servo is also compatible with our Mounting Bracket for Standard-Size Servos:
 |
Note that, as with most hobby servos, stalling or back-driving this servo can damage it.
The FS5103B is a lower-cost alternative to the 3001HB from Power HD, which has nearly identical dimensions and similar performance. The two servos should be generally interchangeable for most applications. The picture below shows both the FS5103B and the 3001HB side by side:
|
| Size: | 40.8 × 20.1 × 38 mm |
|---|---|
| Weight: | 43 g |
| Digital?: | N |
|---|---|
| Speed @ 6V: | 0.16 sec/60° |
| Stall torque @ 6V: | 3.8 kg·cm |
| Speed @ 4.8V: | 0.18 sec/60° |
| Stall torque @ 4.8V: | 3 kg·cm |
| Hardware included?: | Y |
| Lead length: | 12 in |
Note: while this datasheet lists the 6 V stall torque as 3.2 kg*cm, Feetech has since revised this to 3.8 kg*cm based on more recent measurements (this is also more in line with their listed 4.8 V stall torque of 3.0 kg*cm).
 |
Most standard radio control (RC) servos have three wires, each a different color. Usually, they are either black, red, and white, or they are brown, red, and orange/yellow:
Please check the specs for your servo to determine the proper power supply voltage, and please take care to plug the servo into your device in the proper orientation (plugging it in backwards could break the servo or your device).
Note: Some of the servos we carry also have an optional fourth green wire that is separate from the three standard ones. This wire provides access to the feedback potentiometer, allowing you to directly measure the position of the output. The servos with this extra wire have "with Position Feedback" at the ends of their product names. The picture below is an example of such a servo.
 |
FEETECH Sub-Micro Servo FS0403-FB with Position Feedback. |
|---|
We are excited to announce the newest additions to our selection of servos: FEETECH FS90-FB Micro Servo with Position Feedback...