These Micro Metal Gearmotors have low-power (LP), 6 V motors with a stall current of 360 mA and a typical free-run current of 40 mA. The following table shows all of the versions available with the LP 6V motor:
Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.
Versions with other motors are also available. You can use the following selection boxes to choose from all of our Micro Metal Gearmotors versions:
Alternatives available with variations in these parameter(s):
gear ratio motor type encoder
Select variant…
Compare all products in this category
Products in category “6V Low-Power (LP) Micro Metal Gearmotors”
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
4.995:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
2500 RPM, 50 mA |
0.05 kg⋅cm (0.7 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
4.995:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
2500 RPM, 50 mA |
0.05 kg⋅cm (0.7 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
9.96:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
1300 RPM, 40 mA |
0.10 kg⋅cm (1.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
9.96:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
1300 RPM, 40 mA |
0.10 kg⋅cm (1.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
9.96:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
1300 RPM, 40 mA |
0.10 kg⋅cm (1.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
9.96:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
1300 RPM, 40 mA |
0.10 kg⋅cm (1.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
15.25:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
860 RPM, 40 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
15.25:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
860 RPM, 40 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
15.25:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
860 RPM, 40 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
15.25:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
860 RPM, 40 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
29.86:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
450 RPM, 40 mA |
0.29 kg⋅cm (4.0 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
29.86:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
450 RPM, 40 mA |
0.29 kg⋅cm (4.0 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
29.86:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
450 RPM, 40 mA |
0.29 kg⋅cm (4.0 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
29.86:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
450 RPM, 40 mA |
0.29 kg⋅cm (4.0 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
51.45:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
270 RPM, 40 mA |
0.44 kg⋅cm (6.1 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
51.45:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
270 RPM, 40 mA |
0.44 kg⋅cm (6.1 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
51.45:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
270 RPM, 40 mA |
0.44 kg⋅cm (6.1 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
51.45:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
270 RPM, 40 mA |
0.44 kg⋅cm (6.1 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
75.81:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
180 RPM, 40 mA |
0.64 kg⋅cm (8.9 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
75.81:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
180 RPM, 40 mA |
0.64 kg⋅cm (8.9 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
75.81:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
180 RPM, 40 mA |
0.64 kg⋅cm (8.9 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
75.81:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
180 RPM, 40 mA |
0.64 kg⋅cm (8.9 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
100.37:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
130 RPM, 40 mA |
0.74 kg⋅cm (10 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
100.37:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
130 RPM, 40 mA |
0.74 kg⋅cm (10 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
100.37:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
130 RPM, 40 mA |
0.74 kg⋅cm (10 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
100.37:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
130 RPM, 40 mA |
0.74 kg⋅cm (10 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
150.58:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
90 RPM, 40 mA |
1.1 kg⋅cm (15 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
150.58:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
90 RPM, 40 mA |
1.1 kg⋅cm (15 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
150.58:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
90 RPM, 40 mA |
1.1 kg⋅cm (15 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
150.58:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
90 RPM, 40 mA |
1.1 kg⋅cm (15 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
210.59:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
65 RPM, 40 mA |
1.6 kg⋅cm (22 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
210.59:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
65 RPM, 40 mA |
1.6 kg⋅cm (22 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
210.59:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
65 RPM, 40 mA |
1.6 kg⋅cm (22 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
210.59:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
65 RPM, 40 mA |
1.6 kg⋅cm (22 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
248.98:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
54 RPM, 40 mA |
1.7 kg⋅cm (23 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
248.98:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
54 RPM, 40 mA |
1.7 kg⋅cm (23 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
248.98:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
54 RPM, 40 mA |
1.7 kg⋅cm (23 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
248.98:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
54 RPM, 40 mA |
1.7 kg⋅cm (23 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
297.92:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
45 RPM, 40 mA |
2.0 kg⋅cm (27 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
297.92:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
45 RPM, 40 mA |
2.0 kg⋅cm (27 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
297.92:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
45 RPM, 40 mA |
2.0 kg⋅cm (27 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
297.92:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
45 RPM, 40 mA |
2.0 kg⋅cm (27 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
379.17:1 with high-durability steel plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
36 RPM, 40 mA |
2.9 kg⋅cm (40 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
379.17:1 with high-durability steel plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
36 RPM, 40 mA |
2.9 kg⋅cm (40 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
379.17:1 with high-durability steel plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
36 RPM, 40 mA |
2.9 kg⋅cm (40 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
379.17:1 with high-durability steel plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
36 RPM, 40 mA |
2.9 kg⋅cm (40 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
986.41:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
13 RPM, 40 mA |
5.5 kg⋅cm (76 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
986.41:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
13 RPM, 40 mA |
5.5 kg⋅cm (76 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
986.41:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
13 RPM, 40 mA |
5.5 kg⋅cm (76 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
986.41:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
13 RPM, 40 mA |
5.5 kg⋅cm (76 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
4.995:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
2500 RPM, 50 mA |
0.05 kg⋅cm (0.7 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| LP 6V: low-power 6V with precious metal brushes |
4.995:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 6 V |
2500 RPM, 50 mA |
0.05 kg⋅cm (0.7 oz⋅in), 0.36 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
