Comments by Jon

  • Video: Setting the Current Limit on Pololu Stepper Motor Driver Carriers

    Video: Setting the Current Limit on Pololu Stepper Motor Driver Carriers

    - 23 May 2016

    Hello.

    Our stepper motor drivers use current limiting to control stepper motors, but they probably would not be very practical for your application. Instead, we recommend using a dedicated charging IC or circuit, and we do not have any specific recommendations on where to find those.

    -Jon

  • HPCB micro metal gearmotors with extended motor shafts

    HPCB micro metal gearmotors with extended motor shafts

    - 17 May 2016

    Hello.

    As we say in the blog post where we first introduced our micro metal gearmotors with long-life carbon brushes, there are operating conditions under which the carbon brushes allow the HPCB motors to last several times longer than HP versions with precious metal brushes (see that blog post for more information).

    -Jon

  • New revision of the Dual VNH5019 motor driver shield for Arduino

    New revision of the Dual VNH5019 motor driver shield for Arduino

    - 24 February 2016

    Hello, Harry.

    Like we say on the shield's product page: while the shield's overvoltage protection typically kicks in at 27V, it can trigger at voltages as low as 24V, so we do not recommend using this motor driver with 24V batteries, which significantly exceed 24V when fully charged. Specifically what voltage the shield's overvoltage protection kicks in at can vary from unit to unit, so there is a chance that the particular unit you get will not work with a 24V battery.

    -Jon

  • Jon's line following robot: Usain Volt 2.0

    Jon's line following robot: Usain Volt 2.0

    - 2 February 2016

    Hello, MelZero.

    I noticed you made a comment on my Thingiverse web page asking a similar question. I posted a reply there, which is a more appropriate site to talk about this.

    -Jon

  • New product: Advancer Technologies Muscle Sensor v3

    New product: Advancer Technologies Muscle Sensor v3

    - 20 January 2016

    Hello, Ali.

    It is not entirely clear what you are asking (e.g. connect Muscle Sensors to what?), but it sounds like you might be trying to do something complicated or otherwise be looking for more in-depth technical support than is appropriate for blog post comments. Can you refine your questions and either email us or post to our forum?

    Specifically, if you explain in more detail what it is you want to do with two muscle sensors (e.g. what muscle(s) are you sensing, how are you planning on reading the output of the sensors, etc.), we might be able to give you a better idea of whether or not your proposed system could work and maybe refer you to additional documentation for getting started with your project.

    -Jon

  • Video: Setting the Current Limit on Pololu Stepper Motor Driver Carriers

    Video: Setting the Current Limit on Pololu Stepper Motor Driver Carriers

    - 7 January 2016

    Hello.

    We do not have a video that focuses on our A-Star Prime. If you remember that video you were thinking of, we would be interested in seeing it.

    -Jon

  • Jon's line following robot: Usain Volt 2.0

    Jon's line following robot: Usain Volt 2.0

    - 4 January 2016

    Hi, Richard.

    I am glad my write-up was useful! We would love to hear about your car when it is finished, especially if you are using some of our products. For that, you might consider replying here or starting a new thread on the Share Your Projects part of our forum.

    -Jon

  • Using a Maestro to control a quadcopter

    Using a Maestro to control a quadcopter

    - 24 December 2015

    Hello.

    I am not entirely sure who you are addressing, but we did not make the quadcopter featured in this blog post. So, you might get a more detailed response if you ask the person who made this directly. You could start by posting in the thread they shared their project to.

    -Jon

  • The Purdue Tuggiteers' spring 2015 senior design project

    The Purdue Tuggiteers' spring 2015 senior design project

    - 15 December 2015

    Hello, Bob.

    We did not design the tug, so while we do know a few pieces of information about what went into the design for this project, we think it is more appropriate that the students get a chance to respond to your questions. We let them know you commented.

    -Jon

  • Jon's line following robot: Usain Volt 2.0

    Jon's line following robot: Usain Volt 2.0

    - 9 December 2015

    Hello, Richard.

    Sure, I can share those files with you; I'll make them accessible via Thingiverse. However, this is my first time uploading and publishing a creation on Thingiverse, and they require a minimum wait time of 24 hours between account creation and publishing your first creation. For now, I was able to prepare and save a web page that they will be available at, so when it is published (by about this time tomorrow), I expect that you should be able to use this link to access those files.

    As for your laser-cutting question, I am not sure about the least expensive way to get those pieces cut, but you could use our laser-cutting service (and you can ask them specific questions about laser-cutting, too.).

    -Jon

New Products

7.5V, 2.6A Step-Down Voltage Regulator D36V28F7
Case with Fan for RoboClaw 2x15A, 2x30A, and 2x45A
A-Star 32U4 Prime LV (SMT Components Only)
Free Circuit Cellar magazine April 2019
ACHS-7123 Current Sensor Carrier -30A to +30A
A-Star 32U4 Prime LV
Glideforce LACT8P-12V-05 Light-Duty Linear Actuator with Feedback: 25kgf, 8" Stroke (7.8" Usable), 1.7"/s, 12V
Glideforce LACT6P-12V-05 Light-Duty Linear Actuator with Feedback: 25kgf, 6" Stroke (5.9" Usable), 1.7"/s, 12V
DB15 Screw Terminal Adapter for MCP23X/26X Advanced Motor Controllers
Glideforce LACT2P-12V-05 Light-Duty Linear Actuator with Feedback: 15kgf, 2" Stroke (1.97" Usable), 1.7"/s, 12V
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors