Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)

Pololu item #: 3132
Brand: Pololu
Status: Active and Preferred 
RoHS 3 compliant

Price break Unit price (US$)
1 41.95
5 38.59
25 35.51
100 32.67


backorders allowed

The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a TI DRV8834 driver and ships with soldered header pins and terminal blocks. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2 A max with sufficient additional cooling).

Alternatives available with variations in these parameter(s): model connectors soldered? Select variant…

 Description Specs (15) Pictures (8) Resources (16) FAQs (1) On the blog (5) 
I want to control a 3.9 V, 600 mA bipolar stepper motor. Can I use a Tic stepper motor controller that has a minimum operating voltage above 3.9 V without damaging the stepper motor?

Yes. To avoid damaging your stepper motor, you want to avoid exceeding the rated current, which is 600 mA in this instance. All of our Tic stepper motor controllers have configurable current limiting, so you can set a limit that is appropriate for your stepper motor. As long as you set the limit below the rated current, you will be within spec for your motor, even if the voltage exceeds the rated voltage. The voltage rating is just the voltage at which each coil draws the rated current, so the coils of your stepper motor will draw 600 mA at 3.9 V. By using a higher voltage along with active current limiting, the current is able to ramp up faster, which lets you achieve higher step rates than you could using the rated voltage.

If you do want to use a lower motor supply voltage for other reasons, consider using the Tic T834, which operates from 2.5 V to 10.8 V, or the Tic T500, which operates from 4.5 V to 35 V.

Related Products

Tic T500 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)
Tic T500 USB Multi-Interface Stepper Motor Controller
Tic T834 USB Multi-Interface Stepper Motor Controller
Tic T825 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)
Tic T825 USB Multi-Interface Stepper Motor Controller
Tic T249 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)
Tic T249 USB Multi-Interface Stepper Motor Controller
Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller (Connectors Soldered)
Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller
Thin (2mm) USB Cable A to Micro-B, 6 ft, Low/Full-Speed Only
USB Cable A to Micro-B, 6 ft
MP6500 Stepper Motor Driver Carrier, Potentiometer Current Control
MP6500 Stepper Motor Driver Carrier, Digital Current Control
DRV8834 Low-Voltage Stepper Motor Driver Carrier
DRV8825 Stepper Motor Driver Carrier, High Current
TB67S249FTG Stepper Motor Driver Compact Carrier
TB67S249FTG Stepper Motor Driver Carrier - Full Breakout
Pololu High-Power Stepper Motor Driver 36v4
Jrk G2 18v19 USB Motor Controller with Feedback
Jrk G2 24v21 USB Motor Controller with Feedback

Related Categories

Tic Stepper Motor Controllers
DRV8825 Stepper Motor Driver Carriers, High Current
Stepper Motor Drivers
Stepper Motors
Premium Jumper Wires
Wires with Pre-Crimped Terminals
Solderless Breadboards
RC Interface
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors