120:1 Mini Plastic Gearmotor, Offset 2mm Spline Output

Pololu item #: 1122
Brand: PCX
Status: Special Order Only 
RoHS 3 compliant

This product has been discontinued.

This compact, inexpensive, low-current gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range. The splined output shaft has a crest diameter of 2 mm and is offset from but parallel to the motor shaft. The gearbox is protected by a built-in safety clutch that helps protect the gears from excessive loads.

Key specifications:

voltage no-load performance stall extrapolation
4.5 V 120 RPM, 80 mA 1.4 kg⋅cm (20 oz⋅in), 800 mA

Alternatives available with variations in these parameter(s): shaft type no-load speed @ 4.5V extended motor shaft? Select variant…

 Description Specs (11) Pictures (6) Resources (2) FAQs (1) On the blog (0) 
I need additional information about this motor; do you have a datasheet?

No; the information we have available for this motor can be found on its product page. However, you can approximate various additional motor parameters from the information found in the “Specs” tab.

The electrical resistance of the motor can be approximated by dividing the rated voltage by the stall current (at the rated voltage). The electromotive force constant (Ke) can be approximated by dividing the rated voltage by the free-run speed (at the rated voltage). To approximate the motor torque constant (Kt), you can divide the stall torque by the stall current.

For pretty much any DC motor, the current, speed, power, and efficiency curves as a function of torque will look like those in the graph below (assuming motor voltage and temperature are constant):

The current and speed curves are approximately linear, and the product pages for our motors provide the approximate end points for these lines: (0 torque, no-load current) and (stall torque, stall current) for the red line, and (0 torque, no-load speed) and (stall torque, 0 speed) for the blue line.

The orange output power curve is the product of the speed and the torque, which results in an inverted parabola with its peak at 50% of the stall torque.

The green efficiency curve is the output power divided by the input power, where the input power is current times voltage. The voltage is constant, so you can divide the output power curve by the current line to get the general shape of the efficiency curve, which in turn lets you identify the torque, speed, and current that correspond to max efficiency.

There are many programs out there that you can use to generate these curves. For example, if you have access to MATLAB, you can use this customer-created MATLAB script to generate these motor plots for you from the specifications we provide for each gearmotor.

Note: A good general rule of thumb is to keep the continuous load on a DC motor from exceeding approximately 20% to 30% of the stall torque. Stalling gearmotors can greatly decrease their lifetimes, occasionally resulting in immediate damage to the gearbox or thermal damage to the motor windings or brushes. Do not expect to be able to safely operate a brushed DC gearmotor all the way to stall. The safe operating range will depend on the specifics of the gearmotor itself.

Related Products

DRV8835 Dual Motor Driver Carrier
DRV8838 Single Brushed DC Motor Driver Carrier
DRV8833 Dual Motor Driver Carrier
MAX14870 Single Brushed DC Motor Driver Carrier
TB6612FNG Dual Motor Driver Carrier
Baby Orangutan B-328 Robot Controller

Related Categories

Mini Plastic Gearmotors
Motors and Gearboxes
Solarbotics Wheels
Brushed DC Motor Controllers
Brushed DC Motor Drivers
Robot Controllers
Pololu Metal Gearmotors
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors